Protect Your Fuel Tank and Pump With Delphi Technologies
Simple Fixes For Bad Battery Connections
Auto Value, Bumper to Bumper Tech OTY Finalists Named
Protect Your Fuel Tank and Pump With Delphi Technologies
Simple Fixes For Bad Battery Connections
Auto Value, Bumper to Bumper Tech OTY Finalists Named
Sponsored By BCA Bearings by NTN
Sponsored By Carter Fuel Systems
Sponsored By NGK Spark Plugs
AC Diagnostics: Troubleshooting Pressures and Temperatures
The most difficult AC complaints to resolve are the system blows warm, or the air is not as cold as it once was. The causes of the declining performance could be caused by a multitude of components and conditions. In a 45-minute webinar, the experts from Transtar AC will cover the possible causes of AC failure.
The training session will cover:
Speakers Andrew Markel, Director of Technical Content, ShopOwner Dennis Husband, ASE Certified Technician, Transtar AC
Sponsored By BCA Bearings by NTN
ShopOwner includes technical and management content and is free to download and read.
The knock sensor is not the only sensor responsible for detecting engine knock.
Throttle-by-wire systems proactively manage the air and fuel going into the combustion chamber.
Underhood Service targets repair shops that derive 50 percent or more of their revenue from the service and repair of under-the-hood systems. The expanding amount of knowledge and capital needed to keep up with technological advances has led these shop owners to concentrate on underhood systems, while also offering preventive maintenance services on most major vehicle systems. By subscribing, you’ll receive the ShopOwner digital edition magazine (12 times/year) featuring articles from Underhood Service and the Underhood Service eNewsletter (twice weekly). Access to digital editions, contests, news, and more are ready for you today!
Underhood Service targets repair shops that derive 50 percent or more of their revenue from the service and repair of under-the-hood systems. The expanding amount of knowledge and capital needed to keep up with technological advances has led these shop owners to concentrate on underhood systems, while also offering preventive maintenance services on most major vehicle systems. By subscribing, you’ll receive the ShopOwner digital edition magazine (12 times/year) featuring articles from Underhood Service and the Underhood Service eNewsletter (twice weekly). Access to digital editions, contests, news, and more are ready for you today!
High underhood temps, increased power demands and vibration can damage alternators or starters. Sponsored by ACDelco.
Don’t settle for “almost” - it matters where the engine is manufactured or remanufactured. Sponsored by ACDelco.
Brake pads are thoroughly developed to produce the best result. This video is sponsored by ZF Aftermarket.
Click here to view past issues.
Get the latest news, insights, and more delivered directly to you inbox.
Here are the some key installation and service tips to make your next timing belt job just a little easier.
It is always a struggle to remove a crankshaft pulley on a vehicle. The bolt is usually cemented in with thread-locking compound and tightened to over 100-ft./lbs. Specialty tool companies have introduced crankshaft pulley sockets designed to work with impacts. The difference with these sockets is the weight. The extra mass helps your impact to produce more force to remove the bolt. These sockets come in 17mm, 19mm, 21mm and other unique sizes.Advertisement2. Inspect the Vehicle or Get Burned Inspection is the most critical first step that must be performed before the first bolt is removed from the timing belt cover. The inspection needs to include looking for the usual leaks and inspecting items like the oil, motor mounts and accessory drive belt components. You should also scan the vehicle for both active and historical codes. Codes for camshaft and crankshaft synchronization and issues with the variable valve timing system need to be diagnosed first. The inspection has two benefits. First, it spots any items that may limit the life of the new belt. Second, it allows for a more accurate estimate. It can also save you from a dispute with a customer who contends that the problem was not there before the timing belt was replaced.Advertisement3. Time Vs. Mileage If you look at most replacement intervals, you will see a mileage and time period. The time period is just as important as the mileage because the belt is exposed to an environment that breaks down the belt’s materials, even if it is not moving. This type of damage is called oxidation, and it can be caused by oxygen and ozone. 4. Count The Teeth If this one has burned you, you know where I am coming from when I mention counting the number of teeth on the replacement timing belt. In rare cases, the new belt will not be the exact length as the original belt. The change might be due to a cataloging error or the OEM making small changes to the engine that alters the relationship of the crankshaft to the camshaft sprockets. There are two ways to prevent this from happening. First, use the VIN and/or engine code to order the replacement belt. Second, use a high-quality belt that matches the OEM specifications. 5. Balance Shaft Timing On some engines, there are balance shafts that are designed to smooth out the rotational movement of the motor between power pulses. Making sure the marks for the balancer shafts are properly aligned is critical to preventing vibration. Also, some engines have separate belts for the balance shaft that should be replaced with the timing belt. 6. Check the Chain VW, BMW and Hyundai have engines with a timing belt and a timing chain. The chain typically is at the other end of the head and the belt power is just the intake camshaft. The chain runs from the intake camshaft to the exhaust camshaft. There have been reported cases where the chain will jump and cause codes for the crankshaft and camshaft sync codes. Most of these vehicles had high mileage, and the owner neglected to perform oil changes. In most cases, bad oil caused the chain to stretch or the tensioner to fail. Advertisement7. Know Why First If you find a belt with stripped cogs, it would tell you something in the cam drive system has been jammed or is stuck, overloading the belt, and causing it to shear teeth or jump time. The most likely culprit is the camshaft, which may have seized due to engine overheating or lack of lubrication (low oil level or loss of oil pressure). Be sure to check the straightness of the cam bores in the cylinder head, and straighten or align-bore the head as needed before the head goes back on the engine. 8. Take a Picture With the quality of digital cameras in phones these days and the improvements in scan tools, it is possible to take a picture of the old belt on the vehicle to help you make sure the new belt goes on the same way. You might not think that you need it, but it will save you one day. Advertisement9. Replace the Water Pump If the water pump is driven by the timing belt and has not failed during the belt’s replacement interval, there is no guarantee that it will fail during the next service interval. If the pump fails, it could contaminate the belt and even cause tension and alignment problems. It is also an excellent time to perform a cooling system flush and fill because typically the intervals are very close together. 10. Reusing the Belt You may run into a situation where an idler pulley or tensioner has failed long before the replacement interval for the belt has been reached. If the damaged idler or tensioner pulley has caused an alignment problem with the belt, the belt should also be replaced if there are any signs of damage like fraying on the edges or glazing. Advertisement If you have a timing belt tip that we missed, email me at [email protected]
Inspection is the most critical first step that must be performed before the first bolt is removed from the timing belt cover. The inspection needs to include looking for the usual leaks and inspecting items like the oil, motor mounts and accessory drive belt components. You should also scan the vehicle for both active and historical codes. Codes for camshaft and crankshaft synchronization and issues with the variable valve timing system need to be diagnosed first.
The inspection has two benefits. First, it spots any items that may limit the life of the new belt. Second, it allows for a more accurate estimate. It can also save you from a dispute with a customer who contends that the problem was not there before the timing belt was replaced.
If you look at most replacement intervals, you will see a mileage and time period. The time period is just as important as the mileage because the belt is exposed to an environment that breaks down the belt’s materials, even if it is not moving. This type of damage is called oxidation, and it can be caused by oxygen and ozone.
If this one has burned you, you know where I am coming from when I mention counting the number of teeth on the replacement timing belt. In rare cases, the new belt will not be the exact length as the original belt. The change might be due to a cataloging error or the OEM making small changes to the engine that alters the relationship of the crankshaft to the camshaft sprockets. There are two ways to prevent this from happening. First, use the VIN and/or engine code to order the replacement belt. Second, use a high-quality belt that matches the OEM specifications.
On some engines, there are balance shafts that are designed to smooth out the rotational movement of the motor between power pulses. Making sure the marks for the balancer shafts are properly aligned is critical to preventing vibration. Also, some engines have separate belts for the balance shaft that should be replaced with the timing belt.
VW, BMW and Hyundai have engines with a timing belt and a timing chain. The chain typically is at the other end of the head and the belt power is just the intake camshaft. The chain runs from the intake camshaft to the exhaust camshaft. There have been reported cases where the chain will jump and cause codes for the crankshaft and camshaft sync codes. Most of these vehicles had high mileage, and the owner neglected to perform oil changes. In most cases, bad oil caused the chain to stretch or the tensioner to fail.
If you find a belt with stripped cogs, it would tell you something in the cam drive system has been jammed or is stuck, overloading the belt, and causing it to shear teeth or jump time. The most likely culprit is the camshaft, which may have seized due to engine overheating or lack of lubrication (low oil level or loss of oil pressure). Be sure to check the straightness of the cam bores in the cylinder head, and straighten or align-bore the head as needed before the head goes back on the engine.
With the quality of digital cameras in phones these days and the improvements in scan tools, it is possible to take a picture of the old belt on the vehicle to help you make sure the new belt goes on the same way. You might not think that you need it, but it will save you one day.
If the water pump is driven by the timing belt and has not failed during the belt’s replacement interval, there is no guarantee that it will fail during the next service interval. If the pump fails, it could contaminate the belt and even cause tension and alignment problems. It is also an excellent time to perform a cooling system flush and fill because typically the intervals are very close together.
You may run into a situation where an idler pulley or tensioner has failed long before the replacement interval for the belt has been reached. If the damaged idler or tensioner pulley has caused an alignment problem with the belt, the belt should also be replaced if there are any signs of damage like fraying on the edges or glazing.
If you have a timing belt tip that we missed, email me at [email protected]
External Engine: Aging Plastic Intake Components May Cause Leaks
External Engine: Superchargers: Pros And Cons
External Engine: Alternator Testing For No Charge Conditions
External Engine: Runners And Ports: How Modern Engines Manage Air
Technical resources to help diagnose and repair engine-related service issues.